View MSM9564GA_1284819.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

E2F0021-19-31 Semiconductor
Semiconductor MSM9564
IC for FM Multiplex Data Demodulation
This version: Mar. 1999 MSM9564
Pr el ar in im y
GENERAL DESCRIPTION
The MSM9564 is an IC which demodulates FM character multiplex signals in the DARC (Data Radio Channel)*1 format to obtain digital data. The MSM9564 operates at 5 V. The MSM9564 contains on one chip a band pass filter using a switched capacitor filter (SCF) and a group of circuits including frame memory, a frame synchronization circuit, and an error correction circuit. By connecting an external FM receiver and memory for temporary data storage, and microcontroller, a system for obtaining digital data can easily be constructed. The FM multiplex demodulation ICs, the MSM9500-series devices, are configured with minimum functions; so they will, by changing the software of the external microcontroller, be able to respond flexibly to the many FM multiplex broadcast services that are going to come about in the future. The MSM9564 is best suited to radios and information processing devices that support DARC FM multiplex broadcasting. It is also best suited to car radios and car navigation systems that support VICS (Vehicle Information and Communication System), which started its service in 1996. *1 DARC is a registered trademark of NHK Engineering Services. Any manufacturer who has a contract with NHK Engineering Services can produce and sell electronic equipment utilizing the DARC technology. Any manufacturer who has a contract with NHK Engineering Services and VICS Center can produce and sell electronic equipment utilizing the VICS technology.
1/10
Semiconductor
MSM9564
FEATURES
* Built-in VICS-supporting descrambler * Built-in two receive channels including main channel and sub-channel (receives both VICS and D-GPS simultaneously) * Pin compatible with MSM9552/MSM9554 * Internal frame memory enables automatic error correction. * Built-in bandpass filter (SCF) * Built-in block synchronization circuit and frame synchronization circuit * Setting of the number of synchronization protection steps can be changed. * Data clocks are regenerated by digital PLL. * 1T delay detection * Built-in vertical and horizontal error correction circuits * Built-in layer 4 and layer 2 CRC processing circuits * Parallel interface with microcontroller * Clock output for external devices (64 kHz to 8.192 MHz variable) * Compatible with the international standard frame formats A (real time block also supported), B, C * Power supply: 5 V 10% * Package: 44-pin plastic QFP (QFP44-P-910-0.80-2K) (Product name: MSM9564GA)
2/10
Semiconductor
BLOCK DIAGRAM
FM multiplex signal input
LPF
Variable gain AMP
BPF (SCF)
Clock regeneration
Block synchronization
Frame synchronization
Timing control
Clock generator
Timer
INT
Vref SG
Filter Section
PN Descrambler Receive RAM SAEP FRAME memory Error correction & Layer 2 CRC VICS descrambler Layer 4 CRC
IC internal clock
Data bus
Delay Detection Section
Frequency divider
Address bus
1T delay circuit
CPU interface
LPF
Digital Signal Processing Section
XTAL2
XTAL1
Data
Add
RD
WR
CS
CLR
INT
MSM9564
3/10
Semiconductor
PIN CONFIGURATION (TOP VIEW)
MON 1 ADETIN 2 AVDD 3 AGND 4 SG 5 AIN 6 XOUTC 7 MOUT0 8 MOUT1 9
,
44 NC 40 CLR 39 NC 43 NC 42 NC 41 NC
MOUT4 12 MOUT5 13 MOUT6 14 INT 15 WR 16 NC 17
MSM9564
34 A1 33 A0 32 XOUT 31 CS 30 XTAL2 29 XTAL1 28 DVDD 27 DGND 26 DB7 25 DB6 24 DB5 23 DB4
DB3 22
37 A4
DB0 19
36 A3
DB1 20
MOUT2 10 MOUT3 11 RD 18 DB2 21
NC : No-connection pin 44-Pin Plastic QFP
35 A2
38 A5
4/10
Semiconductor
MSM9564
PIN DESCRIPTIONS
Function Microcontroller Interface Pin 16 18 15 31 40 33 to 38 19 to 26 Tuner Interface Analog Section Test Digital Section Test Clock 6 5 1 2 8 to 14 29 30 32 7 Power Supply 3 4 28 27 Symbol WR RD INT CS CLR A0 to A5 DB0 to DB7 AIN SG MON ADETIN MOUT0 to MOUT6 XTAL1 XTAL2 XOUT XOUTC AVDD AGND DVDD DGND Type I I O I I I I/O I O O I O I O O I -- -- -- -- Description Write signal to internal register. Read signal to internal register. Interrupt signal to microcontroller. "L": An interrupt is generated. Chip select signal. "L": Read, write, and data bus signals become active. "L" : the internal registers are initialized and the device enters power down mode. Address signal to internal register. Data bus signal to internal register. FM multiplex signal input. Analog reference voltage output pin. Connect a capacitor between this pin and analog ground to prevent noise. Analog section waveform monitoring pin. The analog block mode setting is specified by the analog control register. Digital signal input pin for testing analog section. Digital section test signal output and monitor output pins. 8.192 MHz crystal connection pin. 8.192 MHz crystal connection pin. Pin for supply of 64 kHz to 8.192 MHz variable clock to the outside. XOUT output control pin. "L" = Clock output, "H" = Output disabled. Pulled up internally. Analog section power supply pin. Analog ground pin. Digital section power supply pin. Digital ground pin.
5/10
Semiconductor
MSM9564
ABSOLUTE MAXIMUM RATINGS
Parameter Power Supply Voltage Input Voltage Output Voltage Maximum Power Dissipation Storage Temperature Symbol AVDD DVDD VI VO PD TSTG Ta = 25C, per package Ta = 25C, per output -- AVDD = DVDD Ta = 25C Condition Rating -0.3 to +7.0 -0.3 to AVDD + 0.3 -0.3 to DVDD + 0.3 400 50 -55 to +150 mW C V Unit
RECOMMENDED OPERATING CONDITIONS
Parameter Power Supply Voltage Crystal Oscillation Frequency Symbol AVDD DVDD fXTAL Condition AVDD = DVDD -- Variable amplifier gain: 1 FM Multiplex Signal Input Voltage Operating Temperature VAIN* Variable amplifier gain: 1.5 Variable amplifier gain: 2 Variable amplifier gain: 3 Top -- Range 4.5 to 5.5
8.192 MHz 100 ppm
Unit V --
Applied Pin AVDD DVDD XTAL1, XTAL2
1.33 to 2.0 1.0 to 1.32 0.66 to 1.0 0.5 to 0.65 -40 to +85 C -- VP-P AIN
*
Peak values (a total voltage of the following signals (a) to (c)) of composite signals including multiplex signals. (a) Voice signals (100% modulated: voice max.) (b) Pilot signal (c) FM multiplex signals (10%: LMSK max.) The maximum amplitude of an input signal is in the range of 2.0 VP-P in which the internal IC circuit is not saturated. Therefore, multiplex signals of up to 2.0 VP-P can be input if only multiplex signals (excluding composite signals) are input from a signal generator.
6/10
Semiconductor
MSM9564
ELECTRICAL CHARACTERISTICS
(DVDD = AVDD = 5 V 10%, DGND = AGND = 0 V, Ta = -40 to +85C) Parameter Symbol Condition When operating, no load Supply Current IDD f = 8.192 MHz When in power down mode, no load BPF Pass Band Attenuation GAIN1 72 to 80 kHz Variable gain amplifier gain: 0 dB 0 to 53 kHz Variable gain amplifier gain: 0 dB 100 to 500 kHz Variable gain amplifier gain: 0 dB Min. Typ. Max. Unit Applied Pin -- -- 18 -- 34 50 mA mA AVDD, DVDD
--
--
3.0
dB
MON
BPF Stop Band Attenuation
GAIN2
50
--
--
dB
MON
BPF Stop Band Attenuation
GAIN3
50
--
--
dB
MON
7/10
Semiconductor
MSM9564
EXTERNAL CONNECTION EXAMPLE
MSM9564
1 Tuner section 330 pF (10%) 2 MON ADETIN CLR A5 A4 A3 A2 A1 A0 40 38 37 36 35 34 33
CPU interface
6 5
AIN SG
2.2 mF (Note 1) (Note 3) (Note 2) 2.2 mF (Note 1)
+ -
XOUT 32 31 CS XTAL2 30 XTAL1 29 15 pF 8.192 MHz crystal 15 pF (Note 2) 2.2 mF (Note 1)
+ -4 14 13 12 11 10 9 8
3
AVDD AGND MOUT6 MOUT5 MOUT4 MOUT3 MOUT2 MOUT1 MOUT0
DVDD
+ 27 - DGND DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 RD WR INT 26 25 24 23 22 21 20 19 18 16 15
28
DVDD AVDD (Note 2) DGND AGND + -
+5 V power supply input
(Note 1) (Note 2) (Note 3)
Use a tantalum capacitor. The AVDD and DVDD should have different paths, respectively. The AGND and tuner ground should use the same ground.
8/10
Semiconductor
MSM9564
APPLICATION CIRCUIT EXAMPLE
Antena
FM tuner
8 bits FM multiplex data demodulation IC MSM9564 SRAM Font ROM LCD control driver CPU (ROM)
LCD display (16 kanji characters 2 lines)
9/10
Semiconductor
MSM9564
PACKAGE DIMENSIONS
(Unit : mm) QFP44-P-910-0.80-2K
Mirror finish
Package material Lead frame material Pin treatment Solder plate thickness Package weight (g)
Epoxy resin 42 alloy Solder plating 5 mm or more 0.41 TYP.
Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, TQFP, LQFP, SOJ, QFJ (PLCC), SHP, and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki's responsible sales person on the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times).
10/10
E2Y0002-29-11
NOTICE
1. The information contained herein can change without notice owing to product and/or technical improvements. Before using the product, please make sure that the information being referred to is up-to-date. The outline of action and examples for application circuits described herein have been chosen as an explanation for the standard action and performance of the product. When planning to use the product, please ensure that the external conditions are reflected in the actual circuit, assembly, and program designs. When designing your product, please use our product below the specified maximum ratings and within the specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating temperature. Oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified operating range. Neither indemnity against nor license of a third party's industrial and intellectual property right, etc. is granted by us in connection with the use of the product and/or the information and drawings contained herein. No responsibility is assumed by us for any infringement of a third party's right which may result from the use thereof. The products listed in this document are intended for use in general electronics equipment for commercial applications (e.g., office automation, communication equipment, measurement equipment, consumer electronics, etc.). These products are not authorized for use in any system or application that requires special or enhanced quality and reliability characteristics nor in any system or application where the failure of such system or application may result in the loss or damage of property, or death or injury to humans. Such applications include, but are not limited to, traffic and automotive equipment, safety devices, aerospace equipment, nuclear power control, medical equipment, and life-support systems. Certain products in this document may need government approval before they can be exported to particular countries. The purchaser assumes the responsibility of determining the legality of export of these products and will take appropriate and necessary steps at their own expense for these. No part of the contents cotained herein may be reprinted or reproduced without our prior permission. MS-DOS is a registered trademark of Microsoft Corporation.
2.
3.
4.
5.
6.
7.
8.
9.
Copyright 1999 Oki Electric Industry Co., Ltd.
Printed in Japan

▲Up To Search▲

Price & Availability of MSM9564GA

	To Download MSM9564GA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .